console init done U-Boot 2012.10 (Jun 27 2019 - 09:59:18) for GK7102S rb-sc1045-v2.0 (GOKE) HAL: 20160804 DRAM: 64 MiB Flash: [BY25Q64AS] USE 1X mode read and 1X mode write 8 MiB NAND: [No SPI nand] SD/MMC: 0 SF: 8 MiB [page:256 Bytes] [sector:64 KiB] [count:128] (BY25Q64AS) In: serial Out: serial Err: serial Net: Int PHY Hit any key to stop autoboot: 0 [PROCESS_SEPARATORS] sf probe;sf read 0xc1000000 0x50000 0x1A0000;bootm 0xc1000000; SF: 8 MiB [page:256 Bytes] [sector:64 KiB] [count:128] (BY25Q64AS) put param to memory mem size (36) total mem size (64) bsb size (1) usr size (0) the kernel image is zImage or Image entry = 0xc1000000 ## Transferring control to Linux (at address c1000000)... Starting kernel ... machid = 3988 r2 = 0xc0000100 Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Linux version 3.4.43-gk (rd@ubuntu) (gcc version 4.6.1 (crosstool-NG 1.18.0) ) #46 PREEMPT Wed Jun 26 13:47:34 CST 2019 [ 0.000000] CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr=00c5387d [ 0.000000] CPU: VIPT aliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Goke IPC Board [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] AHB: 0x90000000 0xf2000000 -- 0x1000000 [ 0.000000] APB: 0xa0000000 0xf3000000 -- 0x1000000 [ 0.000000] PPM: 0xc0000000 0xc0000000 -- 0x200000 [ 0.000000] BSB: 0xc2600000 0xf5000000 -- 0x100000 [ 0.000000] DSP: 0xc2700000 0xf6000000 -- 0x18f0000 [ 0.000000] USR: 0xc3ff0000 0xfe000000 -- 0x10000 [ 0.000000] hal version = 20160804 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 9144 [ 0.000000] Kernel command line: console=ttySGK0,115200 mem=36M rootfstype=squashfs root=/dev/mtdblock2 init=linuxrc mtdparts=gk_flash:320K(U),1664K(K),1152K(R),-(A) [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Memory: 36MB = 36MB total [ 0.000000] Memory: 31712k/31712k available, 5152k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] DMA : 0xff600000 - 0xffe00000 ( 8 MB) [ 0.000000] vmalloc : 0x82800000 - 0xff000000 (1992 MB) [ 0.000000] lowmem : 0x80000000 - 0x82400000 ( 36 MB) [ 0.000000] modules : 0x7f000000 - 0x80000000 ( 16 MB) [ 0.000000] .text : 0x80008000 - 0x80422000 (4200 kB) [ 0.000000] .init : 0x80422000 - 0x80443000 ( 132 kB) [ 0.000000] .data : 0x80444000 - 0x8046c340 ( 161 kB) [ 0.000000] .bss : 0x8046c364 - 0x8049ed58 ( 203 kB) [ 0.000000] NR_IRQS:128 [ 0.000000] >> gk init irq vic1... [ 0.000000] >> gk init irq vic2... [ 0.000000] gk init vic... [ 0.000000] mach gk init timer... [ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] console [ttySGK0] enabled [ 0.020000] Calibrating delay loop... 597.60 BogoMIPS (lpj=2988032) [ 0.080000] pid_max: default: 32768 minimum: 301 [ 0.080000] Mount-cache hash table entries: 512 [ 0.090000] CPU: Testing write buffer coherency: ok [ 0.100000] Setting up static identity map for 0xc054d470 - 0xc054d4a8 [ 0.110000] NET: Registered protocol family 16 [ 0.110000] init timer... [ 0.120000] Init HW timer for DSP communication [ 0.120000] init gpio... [ 0.130000] ################################### [ 0.130000] [BOOT VERSION] GK7102S rb-sc1045-v2.0 v2.0 [ 0.140000] [NET INT_CLK] Internal PHY clock [ 0.140000] [GPIO]############################# [ 0.150000] [GPIO] gpio map get from uboot [ 0.150000] [GPIO CFG] gpio count = 59 [ 0.160000] [GPIO CFG] intphy count = 3 [ 0.160000] [GPIO CFG] extphy count = 3 [ 0.160000] [GPIO CFG] IR LED CTL (55) [ 0.170000] [GPIO CFG] IR CUT1 (55) [ 0.170000] [GPIO CFG] IR CUT2 (55) [ 0.180000] [GPIO CFG] SENSOR Reset (27) [ 0.180000] [GPIO CFG] PHY Reset (55) [ 0.190000] [GPIO CFG] PHY Speed Led (51) [ 0.190000] [GPIO CFG] SPI0 EN (55) [ 0.190000] [GPIO CFG] SPI1 EN (55) [ 0.200000] [GPIO CFG] USB HOST (55) [ 0.200000] [GPIO CFG] SD Detect (32) [ 0.210000] [GPIO CFG] SD Power (55) [ 0.210000] [GPIO CFG] SD1 Detect (63) [ 0.220000] [GPIO CFG] SD1 Power (63) [ 0.220000] [GPIO]############################# [ 0.230000] gpiochip_add: registered GPIOs 0 to 63 on device: gk-gpio0 [ 0.230000] create proc dir [ 0.240000] gk register devices 10 [ 0.240000] gk register I2C [ 0.250000] bio: create slab at 0 [ 0.260000] spi spi.0: gk SPI Controller 0 created [ 0.270000] spi spi.0: master is unqueued, this is deprecated [ 0.270000] spi spi.1: gk SPI Controller 1 created [ 0.280000] spi spi.1: master is unqueued, this is deprecated [ 0.290000] usbcore: registered new interface driver usbfs [ 0.290000] usbcore: registered new interface driver hub [ 0.300000] usbcore: registered new device driver usb [ 0.300000] i2c regbase: 0xf3003000 [ 0.310000] i2c i2c.0: i2c irq:registers 9 [ 0.310000] i2c i2c.0: GK I2C[0] adapter[i2c-0] probed! [ 0.320000] i2c regbase: 0xf3004000 [ 0.320000] i2c i2c.1: i2c irq:registers 58 [ 0.330000] i2c i2c.1: GK I2C[1] adapter[i2c-1] probed! [ 0.340000] FS-Cache: Loaded [ 0.340000] CacheFiles: Loaded [ 0.350000] cfg80211: Calling CRDA to update world regulatory domain [ 0.360000] gk-sd gk-sd.0: Slot0 req_size=0x00010000, segs=16, seg_size=0x00010000 [ 0.390000] gk-sd gk-sd.0: GK SD/MMC[0] has 1 slots @ 50181818Hz, [0x09e130b0:0x00000000] [ 0.400000] NET: Registered protocol family 2 [ 0.400000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.410000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.420000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.430000] TCP: Hash tables configured (established 2048 bind 2048) [ 0.430000] TCP: reno registered [ 0.440000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.440000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.450000] NET: Registered protocol family 1 [ 0.460000] RPC: Registered named UNIX socket transport module. [ 0.460000] RPC: Registered udp transport module. [ 0.470000] RPC: Registered tcp transport module. [ 0.470000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.480000] mdma init... [ 0.490000] mdma request irq: 54 [ 0.490000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.500000] NFS: Registering the id_resolver key type [ 0.510000] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.520000] msgmni has been set to 61 [ 0.530000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.530000] io scheduler noop registered [ 0.540000] io scheduler deadline registered [ 0.540000] io scheduler cfq registered (default) [ 0.550000] uart.0: ttySGK0 at MMIO 0xa0005000 (irq = 31) is a gkuart [ 0.560000] uart.1: ttySGK1 at MMIO 0xa001f000 (irq = 15) is a gkuart [ 0.570000] uart.2: ttySGK2 at MMIO 0xa001e000 (irq = 27) is a gkuart [ 0.580000] brd: module loaded [ 0.590000] loop: module loaded [ 0.590000] adc initialized (10:11) [ 0.600000] speed_mod is 0 [ 0.600000] USE 1X mode read and 1X mode write [ 0.610000] gk_flash gk_flash.0: BH25Q64AS (8192 Kbytes) [ 0.610000] 4 cmdlinepart partitions found on MTD device gk_flash [ 0.620000] Creating 4 MTD partitions on "gk_flash": [ 0.620000] 0x000000000000-0x000000050000 : "U" [ 0.630000] 0x000000050000-0x0000001f0000 : "K" [ 0.640000] 0x0000001f0000-0x000000310000 : "R" [ 0.640000] 0x000000310000-0x000000800000 : "A" [ 0.650000] slram: not enough parameters. [ 0.660000] GKETH_init [ 0.660000] [GKETH_drv_probe] eth_base = 0xf200e000 [ 0.660000] mii id = 0 [ 0.670000] ###### PHY Reset.1.0.2 [ 0.780000] mdiobus_register: PHY[0] whose id 0x00000000 [ 0.790000] goke MII Bus: probed [ 0.790000] gk-eth gk-eth.0: MAC Address[02:11:22:a3:a0:00]. [ 0.800000] usbcore: registered new interface driver cdc_ether [ 0.810000] usbcore: registered new interface driver cdc_wdm [ 0.810000] usbcore: registered new interface driver usbserial [ 0.820000] usbcore: registered new interface driver usbserial_generic [ 0.830000] USB Serial support registered for generic [ 0.830000] usbserial: USB Serial Driver core [ 0.840000] usbcore: registered new interface driver option [ 0.850000] USB Serial support registered for GSM modem (1-port) [ 0.850000] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) [ 0.860000] musb phy Begin initial sequence ... [ 1.170000] gk musb init end... [ 1.170000] dma_controller_create_non_init ok [ 1.170000] musb-hdrc musb-hdrc: MUSB HDRC host driver [ 1.180000] musb-hdrc musb-hdrc: new USB bus registered, assigned bus number 1 [ 1.190000] hub 1-0:1.0: USB hub found [ 1.190000] hub 1-0:1.0: 1 port detected [ 1.200000] musb-hdrc musb-hdrc: USB Host mode controller at f2006000 using DMA, IRQ 26 [ 1.210000] platform add gk musb... [ 1.210000] mousedev: PS/2 mouse device common for all mice [ 1.220000] input: GKInput as /devices/virtual/input/input0 [ 1.230000] Protocol NEC[0] [ 1.230000] ir request irq: 62 [ 1.230000] IR Host Controller probed! [ 1.240000] gk rtc init... [ 1.240000] rtc base: 0xf2080000 [ 1.240000] os read tm: t=0 [ 1.250000] gk-rtc gk-rtc: rtc core: registered gk-rtc as rtc0 [ 1.250000] i2c /dev entries driver [ 1.260000] gk_wdt_v1_00: GK Watchdog Timer, (c) 2014 Goke Microelectronics [ 1.270000] [gk_wdt_init]: init [ 1.270000] [gk_wdt_probe]: probe [ 1.270000] [gk_wdt_probe]: probe mapped wdt_base=f3006000 [ 1.280000] watchdog inactive, reset disabled, irq disabled [ 1.290000] IPv4 over IPv4 tunneling driver [ 1.290000] gre: GRE over IPv4 demultiplexor driver [ 1.300000] ip_gre: GRE over IPv4 tunneling driver [ 1.300000] TCP: cubic registered [ 1.310000] Initializing XFRM netlink socket [ 1.310000] NET: Registered protocol family 10 [ 1.320000] IPv6 over IPv4 tunneling driver [ 1.330000] NET: Registered protocol family 17 [ 1.330000] NET: Registered protocol family 15 [ 1.340000] Registering the dns_resolver key type [ 1.340000] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5 [ 1.350000] os read tm: t=0 [ 1.360000] gk-rtc gk-rtc: setting system clock to 1970-01-01 00:00:00 UTC (0) [ 1.370000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 1.380000] Freeing init memory: 132K [ 1.650000] usb 1-1: new high-speed USB device number 2 using musb-hdrc Starting logging: /etc/init.d/S01logging: line 24: start-stop-daemon: not found /etc/init.d/S01logging: line 24: start-stop-daemon: not found OK Starting mdev... Initializing random number generator... read-only file system detected...done Starting network... /etc/init.d/S40network: line 22: /sbin/ifup: not found GOKE 7102C BOARD START: mkdir: can't create directory '/var/run': File exists Press 'q' in 1 seconds to exit: sh: you need to specify whom to kill [ 5.190000] gpio_dev init suc [ 5.290000] exFAT: Version 1.2.9 /home/start.sh: line 39: /home/custom_init.sh: not found [ 5.890000] hal: module license 'Proprietary' taints kernel. [ 5.890000] Disabling lock debugging due to kernel taint [ 5.930000] crypto initialized (10:11) Media driver version (gcc version 4.6.1 (crosstool-NG 1.18.0) (uClibc)) v2.0.0 #svn r11887 Thu Apr 27 14:04:15 CST 2017 [ 6.220000] request_irq...24 ok-- video_sync [ 6.230000] request_irq...59 ok-- video_frame_last_pixel [ 6.230000] request_irq...61 ok-- video_frame GOKE ADI: R(10836) LIBC(uClibc) (gcc version 4.6[ 6.480000] sensor board reset... .1 (crosstool-NG 1.18.0) ) 2016-10-27 15:58:20 [ 6.760000] detect:gc2053 at 0x6e [ 6.770000] gc2053 i2c read 0x000000f0 is 0x00000020 [ 6.770000] gc2053 i2c read 0x000000f1 is 0x00000053 [ 6.780000] =================================================== [ 6.790000] ================find:gc2053 at 0x6e================ [ 6.790000] =================================================== find:gc2053 at 0x6e rm: can't remove '/tmp/sensor_hw.bin': No such file or directory rm: can't remove '/tmp/sensor_ex.ko.lzma': No such file or directory exec factory_tool.sh ....... ls: /mnt/*-hwcfg.ini: No such file or directory ls: /mnt/*-VOICE.tgz: No such file or directory ls: /mnt/*-ptz.cfg: No such file or directory ls: /mnt/*-hardinfo.bin: No such file or directory ls: /mnt/*-custom_init.sh: No such file or directory umount: can't umount /mnt: Invalid argument tees. build at Jun 20 2019 20:16:42 listen on port 3201. [ 7.890000] initlializing ptz... [ 7.890000] [ 7.890000] Parameters of PTZ driver: [ 7.900000] test_max_pos = 0 [ 7.900000] max_pps = 1000 [ 7.900000] pulse interval: 100/1000 = 0 [ 7.910000] xchg_dir = 2 [ 7.910000] hspd_slfck = 60 [ 7.910000] vspd_slfck = 40 [ 7.920000] hspd_normal = 0 [ 7.920000] vspd_normal = 0 [ 7.920000] hspd_reloc = 30 [ 7.930000] vspd_reloc = 10 [ 7.930000] spd_zoom = 3 [ 7.930000] hmotor_upbound = 496 [ 7.940000] vmotor_upbound = 169 [ 7.940000] zmotor_upbound = 130 [ 7.940000] no_selfck = 0 [ 7.950000] other_flags = 288 [ 7.950000] hmotor_center = 0 [ 7.950000] vmotor_center = 0 [ 7.960000] other_flags: [ 7.960000] 0x0001 --- Return to center when power on [ 7.960000] 0x0002 --- Z-Motor only [ 7.960000] 0x0004 --- No self-check [ 7.960000] 0x0008 --- Ignore position [ 7.960000] 0x0010 --- Respect spd_slfck [ 7.960000] 0x0020 --- No posotion-switch detection [ 7.970000] motor pins: 46,47,42,43,40,41,37,38 [ 7.970000] orig position: <248, 84, 0> [ 7.980000] GK710X gpio ptz(goke timer) device driver[2018.12.14] initialized. sh: 0: unknown operand [ 8.970000] Driver version : v2.1.1_201903061600 [ 8.980000] Fw version : v1.2.2_201902270940 [ 8.980000] [ 8.980000] usb_endpoint_descriptor(0): [ 8.990000] bLength=7 [ 8.990000] bDescriptorType=5 [ 8.990000] bEndpointAddress=81 [ 9.000000] wMaxPacketSize=512 [ 9.000000] bInterval=0 [ 9.000000] Func_Of_Usb_Endpoint_Is_Bulk_In = 1 [ 9.010000] [ 9.010000] usb_endpoint_descriptor(1): [ 9.020000] bLength=7 [ 9.020000] bDescriptorType=5 [ 9.020000] bEndpointAddress=2 [ 9.020000] wMaxPacketSize=512 [ 9.030000] bInterval=0 [ 9.030000] Func_Of_Usb_Endpoint_Is_Bulk_Out = 2 [ 9.040000] [ 9.040000] usb_endpoint_descriptor(2): [ 9.040000] bLength=7 [ 9.040000] bDescriptorType=5 [ 9.050000] bEndpointAddress=3 [ 9.050000] wMaxPacketSize=512 [ 9.050000] bInterval=0 [ 9.060000] Func_Of_Usb_Endpoint_Is_Bulk_Out = 3 [ 9.070000] nr_endpoint=3, in_num=1, out_num=2 [ 9.070000] [ 9.070000] USB_SPEED_HIGH [ 9.340000] ===>passtime: 250 ms [ 9.480000] Func_Of_Proc_Chip_Hw_Config_Rftype RF_Type is 3 TotalTxPath is 1 [ 9.480000] Func_Config_Chip_Outep_Process OutEpQueueSel(0x05), OutEpNumber(2) [ 9.500000] EEPROM type is E-FUSE [ 9.520000] [MC]==> eeValue = 32 [ 9.520000] Boot from EFUSE, Autoload OK ! [ 9.710000] EEPROM VID = 0x2310 [ 9.710000] EEPROM PID = 0x9086 [ 9.710000] drv running in normal mode [ 9.740000] Func_Chip_Hw_Efuseparsepowersavingmode_Process...bHWPwrPindetect(0)-bHWPowerdown(0) ,bSupportRemoteWakeup(1) [ 9.750000] ### PS params=> power_mgnt(0),usbss_enable(0) ### [ 9.780000] kfree Pwr Trim flag:0 [ 10.030000] fw go sucess! [ 10.030000] Func_Chip_Hw_Read_Mac_Hidden_Rpt OK! (1, 0ms), fwdl:1, id:0x19 [ 10.040000] Func_Initwadptdatavariablesbyprom_Process(): REPLACEMENT = 0 [ 10.040000] Func_Of_Proc_Chip_Hw_Read_Chip_Info in 550 ms [ 10.050000] proc_chan_init_func((null)) ChannelPlan ID:0x20, ch num:13 [ 10.060000] NR_RECVBUFF: 16 [ 10.060000] MAX_RECVBUF_SZ: 16384 [ 10.070000] NR_PREALLOC_RECV_SKB: 16 [ 10.070000] wl_new_macid((null)) if1, hwaddr:ff:ff:ff:ff:ff:ff macid:1 [ 10.110000] proc_macaddr_cfg_func mac addr:88:e6:28:a7:c1:47 [ 10.110000] bDriverStopped:True, bSurpriseRemoved:False, bup:0, hw_init_completed:0 [ 10.130000] usbcore: registered new interface driver wll9086xu [ 10.690000] +908621x_drv - drv_open, bup=0 [ 11.940000] MAC Address = 88:e6:28:a7:c1:47 [ 11.940000] -908621x_drv - drv_open, bup=1 [ 11.950000] ADDRCONF(NETDEV_UP): wlan0: link is not ready ifconfig: SIOCGIFFLAGS: No such device [ 11.980000] net eth0: ###### GKETH_start_hw [ 11.990000] net eth0: ###### GKETH_phy_start_aneg... [ 12.000000] ADDRCONF(NETDEV_UP): eth0: link is not ready /home/start.sh: line 253: can't create /sys/class/net/ra0/mtu: nonexistent directory /bin/sh: -l: not found Auto login as root ... goke login: 【APP START】: ========v2 pthread statck size 131072=== eye+ wait. id[0] testMode[0] =============================== ver: 3.4.2.0919 =============================== ========v2 pthread statck size 65536=== ========v2 pthread statck size 65536=== 0: Watchdog started... feed interval 15 seconds. Watchdog wd_setTimeOut [15] complete. gk ic type 1[0- 7102S; 1-7102] gpio15, 4 parts, pinmux reg[0x0]:[0x0], effectValue[1] gpio53, 4 parts, pinmux reg[0x0]:[0x0], effectValue[0] gpio33, 4 parts, pinmux reg[0x0]:[0x0], effectValue[0] gpio12, 4 parts, pinmux reg[0x0]:[0x0], effectValue[1] gpio44, 4 parts, pinmux reg[0x0]:[0x0], effectValue[1] gpio39, 4 parts, pinmux reg[0x0]:[0x0], effectValue[1] ptz/tty, protocol:0, port:0, bps:2400 ptz/tty, protocol:1, port:0, bps:2400 [HW] max_pps : -1 [HW] max_pps : 1000 [HW] xchg_dir : -1 [HW] xchg_dir : 2 [HW] other_flags : -1 [HW] other_flags : 288 [HW] hmotor_upbound : -1 [HW] hmotor_upbound : 496 [HW] vmotor_upbound : -1 [HW] vmotor_upbound : 169 [HW] hspd_normal : -1 [HW] hspd_normal : -1 [HW] vspd_normal : -1 [HW] vspd_normal : -1 [HW] hspd_slfck : -1 [HW] hspd_slfck : -1 [HW] vspd_slfck : -1 [HW] vspd_slfck : -1 [HW] hspd_reloc : -1 [HW] hspd_reloc : -1 [HW] vspd_reloc : -1 [HW] vspd_reloc : -1 ######Get Hardware Info: model:CloudCam, firmware-ident:eyeplus_ipc_gks_001 GPIO: RedLed[-1], BlueLed[15], BoardReset[53] ptzSupport[1], LocalImageAuto[2400] promptVoice[1]... GPIO open success. GIO fd = 6 ERROR: gpio = -1 return ! ERROR: gpio = -1 return ! ERROR: gpio = -1 return ! ERROR: gpio = -1 return ! ERROR: gpio = -1 return ! ERROR: gpio = -1 return ! ERROR: gpio = -1 return ! reset sensor ###### ERROR: gpio = -1 return ! ERROR: gpio = -1 return ! [1970-01-01 08:00:13] [sysInit] silent_reboot_time = 3983 [1970-01-01 08:[ 14.050000] net eth0: ###### GKETH_phy_stop 00:13] [sysInit] sys init finish[ 14.050000] net eth0: ###### GKETH_start_hw ed. Can't open parameter file /[ 14.060000] net eth0: ###### GKETH_phy_start_aneg... home/devParam.da[ 14.070000] device eth0 entered promiscuous mode t on flash, errn[ 14.070000] ADDRCONF(NETDEV_UP): eth0: link is not ready o=0x2. 检测到为海外版本 support all id, langauge check from platform, not from VOICE file. open /etc/passwd file errno=30adjustSysDateFromRTC, read_rtc: 0 [1970-01-01 08:00:13] [checkP2Pfile] GET EYE SER: AJWL191014101PU7ZZHGDV2EZ9038352, SupportAlgrorithm:1, smartAiMode:0 linktest(eth0) = 0 init eth0... set mac of eth0 to : 88:e6:28:a7:c1:47 NET INTERFACE is wlan0 avEncInit start, sensorMode = 26 GOKE ADI: R(12529) LIBC(uClibc) (gcc version 4.6.1 (crosstool-NG 1.18.0) ) 2017-08-09 16:00:24 [PRI] firmware version:3022. Image library version (gcc version 4.6.1 (crosstool-NG 1.18.0) (uClibc)) v2.0.0 #svn r11883 Thu Apr 27 10:01:52 CST 2017 [ 14.500000] =================================================== [ 14.510000] =====gc2053 drv create at 20161117 ver:20170210==== [ 14.520000] =================================================== [ 14.520000] [sensor_get_dev_id 276]find sensor id: 00002053 [ 14.540000] sensor board reset... ===========================gadi_venc_map_dsp call====================== got sensor size: 1920x1080 viParams: resoluMode=0x991e021c, frameRate=25, mirrorMode={0,0} stream_formats: streamId encodeType channelId flipRotate width height xOffset yOffset fps keepAspRat 0 1 0 0 1920 1080 0 0 12 0 1 1 1 0 640 352 0 0 12 0 2 0 2 0 320 180 0 0 12 0 3 2 1 0 640 352 0 0 3 0 h264Conf: streamId brcMode cbrAvgBps gopM gopModel gopN idrInterval profile reEncMode vbrMaxbps vbrMinbps 0 1 400000 1 0 80 1 0 1 786432 80000 1 1 130000 1 0 80 1 0 1 256000 60000 2 1 200000 1 0 50 1 0 1 400000 100000 3 1 200000 1 0 50 1 0 1 400000 100000 chanParams: chan1Type=1, chan1Width=1920, chan1Height=1080 chan2Type=1, chan2Width=640, chan2Height=352 chan3Type=0, chan3Width=320, chan3Height=180 chan4Type=0, chan4Width=0, chan4Height=0 got sensor size: 1920x1080 [ 15.860000] sensor board reset... sensorType2Name, type=26 ----------------[ 16.220000] win_height:0 win_width:0 --venc_video_set[ 16.220000] win_height:0 win_width:0 _qp-------------- qpMaxOnI[37], qpMaxOnP[42], qpMinOnI[34], qpMinOnP[34] sensorType2Name, type=26 ------------------venc_video_set_qp-------------- qpMaxOnI[37], qpMaxOnP[42], qpMinOnI[34], qpMinOnP[34] eye+ wait. id[1] testMode[0] ############################## venc_isp_start########################## start stream[0] start stream[1] start stream[3] gk_isp_daynight sensorModel 32775 isday = 1 getVideoStandard : 0 [gk_isp_daynight]gadi_venc_set_framerate:streamid:0,fps:12 [gk_isp_daynight]gadi_venc_set_framerate:streamid:1,fps:12 gk_isp_daynight: set day mode ----------------->sensorModel == GADI_ISP_SENSOR_GC2053, turn to day! sensorType2Name, type=26 try section isp_gc2053_day... process image.ini section: isp_gc2053_day ae.gainMax = 18 VENC INIT OK! /etc/sensors/gc2053.bin/etc/sensors/gc2053.binbin file name :gc2053 size is 168348 [Loading] sensor bin:gc2053.bin Handle next connect... gk_md_start audio frame size: 160 _audio_ao_start 330568 gadi_audio_ao_set_volume 0xb9 ----------------soundDetectInit: sensitivity[98] ========v2 pthread statck size 65536=== no SD card, do not init record buffer. doSdRecMode mode:0 IsStorageReady() = 0, p_devcfg_param->recordMode=0 [FUN]pda_thread [LINE]1894 face detection init ok ========v2 pthread statck size 65536=== ========v2 pthread statck size 65536=== ========v2 pthread statck size 65536=== ========v2 pthread statck size 65536=== --------------SONG TOOL INIT------------ ========v2 pthread statck size 65536=== ========v2 pthread statck size 65536=== ========v2 pthread statck size 65536=== ========v2 pthread statck size 65536=== start check system time!!!!!! lib ctp. v20190625 CTP Server Started at 8001 setsockopt IP_ADD_MEMBERSHIP: No such device ctp_proc_live_video, mt=1 -------------------eye+ init--------------- vendor.moduleid: eyeplus_ipc_gks_001 =============CreateDevicePtz OK ============= CreateDevicePlayback eye+ sdk version: 10878 get_ipaddr ioctl error and errno=99 interface_name = wlan0 ---------ip got, start onvif----------- ------------uuid is 1df2e14e-1dd2-11b2-8323-88e628a7c147 and mac = 88e628a7c147 getMainStreamVideoSize: w 1920 h 1080 [res = 0x0] getMainStreamVideoSize: w 1920 h 1080 [res = 0x0] getMainStreamVideoSize: w 1920 h 1080 [res = 0x0] getMainStreamVideoSize: w 1920 h 1080 [res = 0x0] Thu Jan 1 08:00:17 CST 1970 ----------->GetDeviceId buf AJWL191014101PU7ZZHGDV2EZ9038352 --------------DevSystem_GetMacAddr MAC: 88e628a7c147 [ 19.420000] net eth0: ###### GKETH_phy_stop stat GatherWifiSetting++++++++++++++++++++++++++++ GatherWifiSetting......... ========v2 pthread statck size 131072=== ========v2 pthread statck size 65536=== start get vi frame GetDefaultConfig, get DeviceType: {"gateway":"Off"} APModePlay = Yes TransmitStatistics = No LiveCtrl = Yes APModePlay = Yes APModePlay = Yes -->lable index is to max, 9303,9499 cur 1275, total:4000, max! AudioEncode = G711A inlanPlay = Yes LedSwitch: 1 [OnStatus]--------status: 0x101 [OnStatus]--------device have no account! random: Trying to read entropy from /dev/random Configuration file: /tmp/hostapd.conf drv->ifindex=6[ 22.020000] left_aps..... l2_sock_recv==[ 22.020000] set_mode = IW_MODE_MASTER l2_sock_xmit=0x0x28a570 BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits) Allowed chan[ 22.040000] Func_Of_Proc_Hostapd_Sta_Flush nel: mode=1 chan=1 freq=2412 MHz max_tx_power=0 dBm Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=0 dBm Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=0 dBm Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=0 dBm Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=0 dBm Allowed channel: mode=1[ 22.080000] flush_sta_func(wlan0) chan=6 freq=243[ 22.080000] deauth_to_pre_issue_func to ff:ff:ff:ff:ff:ff 7 MHz max_tx_pow[ 22.090000] Func_Of_Proc_Set_Encryption er=0 dBm Allowe[ 22.090000] clear default encryption keys, keyid=0 d channel: mode=1 chan=7 freq=2442 MHz max_tx_po[ 22.100000] Func_Of_Proc_Set_Encryption wer=0 dBm Allow[ 22.110000] clear default encryption keys, keyid=1 ed channel: mode=1 chan=8 freq=2[ 22.120000] Func_Of_Proc_Set_Encryption 447 MHz max_tx_p[ 22.120000] clear default encryption keys, keyid=2 ower=0 dBm Allo[ 22.130000] Func_Of_Proc_Set_Encryption wed channel: mod[ 22.140000] clear default encryption keys, keyid=3 e=1 chan=9 freq=2452 MHz max_tx_power=0 dBm Allowed channel: mode=1 chan=10 fre[ 22.150000] Func_Of_Proc_Set_Beacon, len=71 q=2457 MHz max_t[ 22.150000] check_beacon_data_func, len=57 x_power=0 dBm Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=0 dBm Allowed channel: mode=1 chan=12 freq=2467 MHz max_tx_power=0 dBm Allowed channel: mode=1 chan=13 freq=2472 MHz max_tx_power=0 dBm Allowed channel: mode=1 chan=14 freq=2484 MHz max_tx_power=0 dBm Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=0 dBm Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=0 dBm Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=0 dBm Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=0 dBm Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=0 dBm Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=0 dBm Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=0 dBm Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=0 dBm Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=0 dBm Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=0 dBm Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=0 dBm Allowed channel: mode=2 chan=36 freq=5180 MHz max_tx_power=0 dBm Allowed channel: mode=2 chan=40 freq=5200 MHz max_tx_power=0 dBm Allowed channel: mode=2 chan=44 freq=5220 MHz max_tx_power=0 dBm Allowed channel: mode=2 chan=48 freq=5240 MHz max_tx_power=0 dBm Allowed channel: mode=2 chan=52 freq=5260 MHz max_tx_power=0 dBm Allowed channel: mode=2 chan=56 freq=5280 MHz max_tx_power=0 dBm Allowed channel: mode=2 chan=60 freq=5300 MHz max_tx_power=0 dBm Allowed channel: mode=2 chan=64 freq=5320 MHz max_tx_power=0 dBm Allowed channel: mode=2 chan=100 freq=5500 MHz max_tx_power=[ 22.300000] chbw_decision_of_ap_func(wlan0) ld_sta_num:0, lg_sta_num0, ap_num:0 0 dBm Allowed channel: mode=2 chan=104 freq=5520 MHz max_tx_power=0 dBm Allowed channel: mode=2 chan=108 freq=5540 MHz max_tx_power=0 dBm Allowed channel: mode=2 chan=112 freq=5560 MHz max_tx_power=0 dBm Allowed channel:[ 22.320000] chbw_decision_of_ap_func(wlan0) req: 3,0,0 mode=2 chan=116[ 22.330000] chbw_decision_of_ap_func(wlan0) dec: 3,0,0 freq=5580 MHz max_tx_power=0 dBm Allowed channel: mode=2 chan=120 freq=5600 MHz max_tx_power=0 dBm Allowed ch[ 22.350000] HW_VAR_BASIC_RATE: 0x15f -> 0x15f -> 0x15f annel: mode=2 chan=124 freq=5620 MHz max_tx_power=0 dBm Allowed channel: mode=2 chan=128 freq=5640 MHz max_tx_power=0 dBm Allowed channel: mode=2 chan=132 fre[ 22.370000] supp_mcs_set = 00, 00, 00, rf_type=130, tx_ra_bitmap=000000000000000f q=5660 MHz max_t[ 22.370000] do_query_tx_nss: 1 SS, rf_type=3 x_power=0 dBm A[ 22.380000] bmc_sta_update_func=> mac_id:1 , raid:8 , bitmap=0x000000000000000f llowed channel: [ 22.390000] Func_Of_Proc_Chip_Hw_Add_Ra_Tid(): mac_id=1 raid=0x8 bw=0 mask=0xf mode=2 chan=136 freq=5680 MHz max_tx_power=0 dBm Allowed channel: mode=2 chan=140 freq=5700 MHz max_tx_power=0 dBm Allowed channel: mode=2 chan=149 freq=5745 MHz max_tx_power[ 22.420000] Func_Of_Set_Fwmacidconfig_Cmd(): mac_id=1 raid=0x8 bw=0 mask=0xf =0 dBm Allowed channel: mode=2 chan=153 freq=5765 MHz max_tx_power=0 dBm Allowed channel: mode=2 chan=157 freq=5785 MHz max_tx_power=0 dBm Allowed channel: mode=2 chan=161 freq=5805 MHz max_tx_power=0 dBm Allowed channel: mode=2 chan=165 freq=5825 MHz max_tx_power=0 dBm Completing interface initialization Mode: IEEE 802.11g Channel: 3 Frequency: 2422 MHz RATE[0] rate=10 flags=0x1 RATE[1] rate=20 flags=0x1 RATE[2] rate=55 flags=0x1 RATE[3] rate=110 flags=0x1 RATE[4] rate=60 flags=0x0 RATE[5] rate=90 flags=0x0 RATE[6] rate=120 flags=0x0 RATE[7] rate=180 flags=0x0 RATE[8] rate=240 flags=0x0 RATE[9] rate=360 flags=0x0 RATE[10] rate=480 flags=0x0 RATE[11] rate=540 flags=0x0 Flushing old station entries Deauthenticate all stations +rtl871x_sta_deauth_ops, ff:ff:ff:ff:ff:ff is deauth, reason=2 rtl871x_set_key_ops rtl871x_set_key_ops rtl871x_set_key_ops rtl871x_set_key_ops Using interface wlan0 with hwaddr 88:e6:28:a7:c1:47 and ssid 'CLOUDCAM_88e628a7c147' Using existing control interface directory. rtl871x_set_beacon_ops rtl871x_set_hidd[ 22.520000] Func_Of_Proc_Set_Hidden_Ssid(wlan0) ignore_broadcast_ssid:0, CLOUDCAM_88e628a7c147,21 en_ssid ignore_broadcast_ssid:0, CLOUDCAM_88e628a7c147,21 get_ipaddr ioctl error and errno=99 interface_name = wlan0 rtl871x_set_acl wlan0: Setup of interface done. [ 22.560000] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready wifi ap CLOUDCAM_88e628a7c147 started ... killall: dhcpd: no process killed SoftAPThread terminated. -->lable index is to max, 8006,18914 cur 1752, total:4000, max! ------playSound /tmp/VOICE/Please_configure_camera_by_AP_hotspot_or_scanning_code.wav =============>DevVideo_GetSize called getMainStreamVideoSize: w 1920 h 1080 [res = 0x0] playHiAudioFile start /tmp/VOICE/Please_configure_camera_by_AP_hotspot_or_scanning_code.wav.. gk_isp_daynight sensorModel 32775 isday = 1 getVideoStandard : 0 [gk_isp_daynight]gadi_venc_set_framerate:streamid:0,fps:12 [gk_isp_daynight]gadi_venc_set_framerate:streamid:1,fps:12 gk_isp_daynight: set day mode ----------------->sensorModel == GADI_ISP_SENSOR_GC2053, turn to day! sensorType2Name, type=26 try section isp_gc2053_day... process image.ini section: isp_gc2053_day ae.gainMax = 18 #####IR CUT in Day Mode2. -->lable index is to max, 7692,13141 -->lable index is to max, 7724,12947 cur 1385, total:4000, max! -->lable index is to max, 8331,14672 cur 1189, total:4000, max! -->lable index is to max, 7489,13085 cur 2521, total:4000, max! -->lable index is to max, 7636,12658 cur 2435, total:4000, max! -->lable index is to max, 7596,12906 cur 1750, total:4000, max! -->lable index is to max, 7524,13467 cur 2803, total:4000, max! -->lable index is to max, 7741,13047 -->lable index is to max, 8037,13366 cur 1118, total:4000, max! -->lable index is to max, 8207,13749 cur 1499, total:4000, max! -->lable index is to max, 8324,15400 -->lable index is to max, 6886,8086 -->lable index is to max, 7072,8371 ------playSound /tmp/VOICE/Please_configure_camera_by_AP_hotspot_or_scanning_code.wav over -->lable index is to max, 6971,7169 -->lable index is to max, 7501,7844 -->lable index is to max, 8261,8604 -->lable index is to max, 5907,8388 -->lable index is to max, 6746,10508 -->lable index is to max, 6819,11346 -->lable index is to max, 6436,8693 -->lable index is to max, 6009,6664 -->lable index is to max, 7158,8375 -->lable index is to max, 8307,9261 -->lable index is to max, 8969,14474 -->lable index is to max, 7722,10771 -->lable index is to max, 7525,10225 -->lable index is to max, 6318,9656 -->lable index is to max, 6607,8893 -->lable index is to max, 12934,12944 -->lable index is to max, 7838,11034 -->lable index is to max, 6964,10280 -->lable index is to max, 6371,8279 -->lable index is to max, 6825,11404 -->lable index is to max, 7763,11931 cur 3472, total:4000, max! -->lable index is to max, 6387,8790 Login timed out Auto login as root ... localhost login: localhost login: localhost login: root Password: Login incorrect localhost login: admin Password: Login incorrect localhost login: root Password: ===============>watchdog counter 2(smartlink)(n:48,to:45) timeouted! Login incorrect Jan 1 08:02:07 Auto login as root ... localhost login: 2019